micro spring ? air core inductors document 163-1 document 163-1 revised 10/13/15 part inductance 2 percent q 4 srf min 5 dcr max 6 i rms 7 number 1 turns (nh) tolerance 3 min (ghz) (mohm) (a) 0906-2_l_ 2 1.65 10 ,5 100 10.0 4.0 1.6 0906-3_l_ 3 2.55 5,2 ,1 100 8.2 5.0 1.6 0906-4_l_ 4 3.85 5,2 ,1 100 7.5 6.0 1.6 0906-5_l_ 5 5.40 5,2 ,1 100 7.0 8.0 1.6 1606-6_l_ 6 5.60 5,2 ,1 100 6.5 9.0 1.6 1606-7_l_ 7 7.15 5,2 ,1 100 6.0 10 1.6 1606-8_l_ 8 8.80 5,2 ,1 100 6.0 12 1.6 1606-9_l_ 9 9.85 5,2 ,1 100 5.2 13 1.6 1606-10_l_ 10 12.55 5,2 ,1 100 4.6 14 1.6 1. when ordering, specify tolerance, termination and packaging codes: 1606-10 glc tolerance: f = 1% g = 2% j = 5% k = 10% (table shows stock tolerances in bold.) termination: l = rohs compliant tin-silver (96.5/3.5) over copper. special order: t = rohs tin-silver-copper (95.5/4/0.5) or s = non-rohs tin-lead (63/37). packaging: c = 7 machine-ready reel. eia-481 embossed plastic tape, 500 parts per full reel. b = less than full reel. in tape, but not machine-ready. to have a leader and trailer added ($25 charge), use code letter c instead. terminations rohs compliant tin-silver over copper other termina - tions available at additional cost. weight 0906: 10 C 12 mg; 1606: 18 C 27 mg ambient temperature C40c to +125c with i rms current maximum part temperature +140c (ambient + temp rise) storage temperature component: C40c to +140c. tape and reel packaging: C40c to +80c resistance to soldering heat max three 40 second refows at +260c, parts cooled to room temperature between cycles temperature coeffcient of inductance (tcl) +5 to +70 ppm/c moisture sensitivity level (msl) 1 (unlimited foor life at <30c / 85% relative humidity) failures in time (fit) / mean time between failures (mtbf) one per billion hours / one billion hours, calculated per telcordia sr-332 packaging 0906: 500 per 7 reel plastic tape: 8 mm wide, 0.3 mm thick, 4 mm pocket spacing, 1.5 mm pocket depth 1606: 500 per 7 reel plastic tape: 12 mm wide, 0.3 mm thick, 4 mm pocket spacing, 1.6 mm pocket depth recommended pick and place nozzle: od: 0.059 ; id: 0.035 pcb washing tested to mil-std-202 method 215 plus an additional aqueous wash. see doc787_pcb_washing.pdf . ? small air core inductors feature high q and tight tolerances ? acrylic jacket provides a fat top for pick and place ? solder coated leads ensure reliable soldering 2. inductance measured at 800 mhz using agilent/hp 4286 or equivalent with a coilcraft smd-a fxture and correlation. 3. tolerances in bold are stocked for immediate shipment. 4. q measured at 800 mhz using an agilent/hp 4291a with an agilent/ hp 16193a test fxture or equivalents. 5. srf measured using an agilent/hp 8720d or equivalent with a coilcraft smd-d fxture. 6. dcr tested on the cambridge technology model 510 micro-ohmmeter or equivalent. 7. current that causes a 15c temperature rise from 25c ambient. this information is for reference only and does not represent absolute maxi - mum ratings. 8. electrical specifcations at 25c. refer to doc 362 soldering surface mount components before soldering.
document 163-2 document 163-2 revised 10/13/15 micro spring? air core inductors typical l vs frequency C 0906 series typical l vs frequency C 1606 series 0 2 4 6 8 10 12 14 100 1000 frequency (mhz) inductance (nh) 3.85 nh 2.55 nh 1.65 nh 5.40 nh 0 2 4 6 8 10 12 14 100 1000 frequency (mhz) inductance (nh) 12.55 nh 9.85 nh 8.80 nh 7.15 nh 5.60 nh typical q vs frequency ? 0906 series typical q vs frequency ? 1606 series 0 50 100 150 200 250 100 1000 frequency (mhz) q factor 1.65 nh 2.55 nh 3.85 nh 5.40 nh 0 50 100 150 200 250 100 1000 frequency (mhz) q factor 7.15 nh 12.55 nh 8.80 nh 5.60 nh 9.85 nh designer?s kit c308 contains 12 each of all values. designers it c308-2 contains12 each of all 2% values. siz ea maxb max c max de f max 0906 0.095 0.060 0.072 0.135 0.055 0.010 0.010 0.020 2,41 3,43 1,52 1,40 0,25 1,83 0,25 0,51 1606 0.165 0.135 0.062 0.055 0.010 0.144 0.012 0.020 4,19 3,43 1,58 1,40 0,25 3,66 0,30 0,51 recommended land p atterns 0906 size 1606 siz e 0.031 0,79 0.031 0,79 0.144 3,66 0.072 1,83 0.097 2,46 0.097 2,46 0.040 1,02 0.040 1,02 a b d c e f strip length 135 max 0 min pic k and place surf ace dimensions are in inches mm
|
